UZIN Materials & Cost Job Calculator

Fill in all highlighted areas and then click the 'Calculate' button below or use the Enter key.

UZIN Leveling Compounds

NC 110 / NC 144 LW / NC 147 CG / NC 150 / NC 150 F / NC 157 / NC 170 / NC 172

Depth Bags Needed Total Cost Cost /sf

UZIN PE 460 Moisture Vapor Retarder

*Surface porosity will cause coverage rates to vary. Your coverages may differ.

2.5 gallon metal combi-can

*Coverage Rate Pails Needed Total Cost Cost /sf
1270 s/f per pail 1 $0.00 $0.00
1Trowel/Squeegee 1-coat method

Uzin PE 414 Turbo Surface Strengthener/MVR

*Surface porosity will cause coverage rates to vary. Your coverages may differ.

2.6 gallon plastic jug

*Coverage Rate Pails Needed Total Cost Cost /sf
11500 s/f per pail 1 $0.00 $0.00
21500 s/f per pail 1 $0.00 $0.00
31500 s/f per pail 1 $0.00 $0.00
1Surface Strengthener with 1 coat / 2 Moisture Retarder with 2 coats / 3 Moisture Retarder with 3 coats (grit binding)

UZIN 1PE 280 Primer & Bonding Agent

*Surface porosity will cause coverage rates to vary. Your coverages may differ.

2.6 gallon plastic pail

*Coverage Rate Pails NeededTotal Cost Cost /sf
1200 s/f per pail 1 $0.00 $0.00
21850 s/f per pail 1 $0.00 $0.00
1Do not use as a primer under hardwood flooring
21850 square feet is the coverage rate used for the Max Moisture System

UZIN PE 260 Primer & Bonding Agent

*Surface porosity will cause coverage rates to vary. Your coverages may differ.

2.6 gallon plastic jug

*Coverage Rate Pails Needed/1FS Total CostCost /sf
1800 s/f per pail 1 $0.00 $0.00
21400 s/f per pail 1 $0.00 $0.00
32100 s/f per pail 1 $0.00 $0.00
42700 s/f per pail 1 $0.00 $0.00
1FS = full strength / 21:1 dilution ratio / 31:2 dilution ratio / 41:3 dilution ratio

UZIN PE 360 Plus Dispersion Primer (abs.)

*Surface porosity will cause coverage rates to vary. Your coverages may differ.

2.6 gallon plastic jug

*Coverage Rate Pails NeededTotal Cost Cost /sf
1600 s/f per pail 1 $0.00 $0.00
1Do not dilute; only use full strength
w/Leveling per sq foot: $ 0.00

**Includes PE 460, PE 280 and **n/a of leveling compound.

Note: The Max Moisture System above that incorporates UZIN PE 280 requires a minimum SLC depth of 1/8” and a maximum SLC depth of ½”. You will have to use the sand grit binding method for depths above ½”. In certain cases, you may use this system up to 1” depth. Please refer to the UZIN PE 280 data sheet for more information.

IMPORTANT NOTE: The information, calculations and formulas found in this calculator are subject to change at any time. Final determination of project volumes rests with the application contractor.

Proper substrate preparation starts with a thorough inspection and assessment of jobsite conditions to determine what concerns need to be addressed to meet the specification and to ensure a successful installation for the life of the floor covering. When assessing a substrate, the flooring contractor must take into consideration the type of flooring, area in which it will be used and the stresses it will be subjected to during its service life. Improper or inadequate assessment and substrate preparation leads to construction delays, costly repairs and/or premature failure of the flooring system. Contact the UZIN Technical Services Department for additional clarification / 866.505.4810 / www.uzin.us/support/customer-service/ / uzin.us@uzin-utz.com